Transpower India Electronics Pvt. Ltd.

These transformers are designed to work in single phase, two phase as well as three phase to handle required power upto 8KVA. This series of transformers are avilable with/without shield with multiple outputs. Also avaible with internal thermal fuses or external replacable slowblow Fuse. 

Features:-

• Low Loss, Low Leakage Inductuance
• Better regulation and thus less heat dissipation
• Different types of mountings and orientation to suit customers need in placement
• Insulation level to with stand class B, E, C, H
• Specifications as per EN61558-2-2, 2-4, IS6297, IS2026, IS11171
•  

 If you are looking for stepdown transformers with less than 20VA rating, our PT/VCT series are ideal selection.

Features:-

• Wide range in Single, Two and Three Phase
• Multiple Secondary Outputs
• Compact and different shapes and sizes to suit customer needs.
• Flying Leads type or Pin Type
• Vaccum resin Moulded / Shell type.
• Thermal Cut-off protection
• Specifications as per EN 61558 2-2, 2-6, IS3156, IS6297
• 
  

Isolation Transformers are used to protect equipments from unwanted signals, spikes (and off course to Isolate your system). Our IT series Transformers are available in single, two and three phase.

Features:-

• Low magnetic Leakage
• Optimized Horizontal and Vertical Construction to fit in your equipment.
•  Available with or without Enclosure
• Option in Mounting and Termination
• Good attentuation against radio interference and spkies.
• Suitable for high end euipments at lab, home and hospitals.
• Specifications as per EN61558 2-4, 2-6, IS6297, IS2026, IS11171
• 

Dry Type Power Transformers suitable for any equipments, panels,machinaries and processing plant for step up / step down application upto 25KVA rating are available in single, two and three phase source. Tempreture rise and Insulation level as per IEC and IS standard.

 Our Dry Type Three Phase Distribution Transformer are avilable upto 250KVA, 3.3KV. They are Designed for indoor application, Guranteed to operate continuosly at its rated KVA at maximum 50 degree Celcius Ambient.

Features:-

• Compact enough to handle maximum power
• Insulation class of B, E, C, H
• IP series Enclosure as per yourneeds
• Better Regulation
• Long Life and wide range
• Specifications as per EN61558-1-2, IS2026-1-4, IS1171
• 

High Volatge Transformers from 1 VA to 20KVA upto 24KV Operation either in encapsulted or with IP65 Blast Proof enclosure are also in our scope of supply. In house Test Facility to conduct almost test parameters mentioned in EN61558 1-2 4-6, IS2026 and IS11171 ensures performance of each and every unit with long life.

Features:-

• Compact Enough to handle maximum power.
• Long life and wide range
• Specification as per EN61558 1-2 4-6, IS2026, IS11171

The following types of transformers are also in our range.

• Phase shift Transformers upto 200KVA with phase shift of any angle.
• Synchronous Transformers
• Voltage Control Transformers for measurement.
• Protection Transformers
• Combined current and volatge transformers
• 12 pulse, 24 pulse transformers for converters.

AC Reactors are intended for series connection in a system for limiting current or for load sharing purpose are available in wide range of current rating and inductance value.

DC Reactors to filter out harmonics present in DC power systems of high or low system voltages are available. Supressing harmonics of any frequency range with lesscore loss is an essence in our DC reactor design.

Features:-

• Tailor made design to suit customer requirement
• Single and Three Phase AC Reactors
• Current upto 3000A, L value from uH to mH
• Air Core / Iron Core Reactors
• Linear Characteristics (unless customer requirement differs.)
• Optimum Design
• Rugged Construction Low Noise.
• IP Series Enclosure (option) 

 Features:-

• Measurement CT's , Protection CT's, Core Balance CT's, dual purpose CT's , Special Purpose CT's
• Indoor / Outdor Type
• Tape Insulated CT's, Resin casted, ABS casing
• Ring Type, Bar Type
• To use in normal or upto 24KV system voltages
• Class of Accuracy 0.2, 0.5, 0.5S, 1, 5 etc.
• Rated Burden 0.1VA to 25VA
• Tailor made
• Specifications as per IS2705
• 

TIE Range of Switching Transformers are available from 2 watts to 5000 watts for flyback, forward, push pull, half bridge and full bridge configuration power supplies. These are available in different core geometries like EI, EE, EC, RM, EF, ETD, ER and Pot Core with various type of mounting like clamp or pin configurations. Highcurrent (foil wound), high voltage switching transformers are also availbe.

 Features:-

• Compact, High efficiency, maximum power handling with less temperature rise
• Flame retardant with sturdy terminals made to prevent breaking of lining
• High Flux density, High Permeability, low loss are used to acheive High efficiency with low power loss.
• Creapage / Clearance distance between Input and output with class H Insulation film or flame retardant tape to ensure High Voltage Isolation
• Moisture proof, vibration proof, and shock proof through perfect engineering. 
• 

 We manufcature wide range of pulse / driver transformers with different core materials like amorphous alloy, nano crystalline, ferrite core etc.

Features:-

• Compact Design
• High Insulation Level
• Low coupling Capacitance and thus High Degree of Immunity from interference.
• Low leakage indcutance
• Least switch on or Off delays
• Transmission high Instantaneous power
• Wide range of operating temperature
• National and International Standards  eg. EN5018, EN60950
• 

Common Mode Chokes are widely used supress / block radio frequency interference from generating at source to main line and vice versa.

Features:-

• Single phase, Three Phase
• Wide current range 0.2A to 30A
• High permeability, Compact Size, High Attenuation
• Wide range Suits many type of equipments
• High insulation between live leads
• Pin type, Surface Mounting Type

SMPS and DC-DC Converters from 1 watt to 1000 watts are available in different geometries. upto 20 watts these are available in moduclar form either with pcb mounting or surface mounting. Tailor made power supplies, DC-DC Converters to suit your requirement can be designed and manufactured.

Specifications:-

• Input Range: upto 240V AC/DC +-30%
• Ouput Range: upto 200V (in multiple outputs)
• Raing: upto 1000 watts
• Regulation: 1%
• Ripple: less than 0.1%
• Isolation: upto 2.5 KV
• Housing: As per your requirement.
•